I think I have finally finished this one…….

Just picked up my first can, an Omega 36M. Ran it today on my MPX with generic plinking FMJs. After it cooled and I took the can off, I found this debris. Is this normal for first time running? Did not find any evidence of a baffle strike. Some of the debris appears to be powder, while the other portion appears metallic. Some of the 9mm I was running had brass colored jackets, so potentially that?
Again, super noob to this, so hoping to get any guidance I can.

My 21st birthday was Saturday went and filled the paperwork out and got approved to pick it up yesterday. Couldn’t be more happy about it.

Is Comstock brake good to go with a polo k on standard Rearden atlas hub, like not to close to blast chamber? I tried looking at the charts but my brain instantly fried and is still recovering

Ordered on may 5th and received today, July 22nd. Between .22LR and .25ACP I chose .22LR. I’m very excited to get out and shoot it.

Sadly haven’t found a SureFire Monster or Mini Monster to spend even more irresponsible amounts of money on, so you’ll have to forgive me for having an RC2 on it. One day she’ll be complete though.

BOE IL9S on a trust (46 days) and factory 10/22 SBR as an individual (14 days).

The worst part was waiting in silence hoping I didn't fill my form 1 out wrong. Now I have to figure out suppressors. Anyone here have recommendations for good quality?

u/BOE-Suppression u/Comstock-Support

So previously posted about alignment being off with newly purchased Comstock plan b flash hider and low profile hub mount on BOE incolite 9m. I Disassembled and reassembled with direct mount that came with suppressor and alignment rod is pretty well centered (pic 1). Disassembled and dry fit Comstock plan b system again and alignment rod is touching end of suppressor at about the 10:00 position. Took off Suppressor and ran alignment rod with just flash hider and alignment rod is almost touching 10:00 position of flash hider. So at this point can I conclude the flash hider is causing the problem?

Does anyone have link to an article or video showing the current steps on setting up an NFA gun trust?

I’m looking to buy my first can. Don’t usually have a problem, but my ADHD is pretty bad when it comes to things legal forms.

It be easier on me if I knew what steps to expect.

Thank you!

As I look into the material of a supressor Im favoring a Ti for my hunting rifles. I do want to be able to swap it to an AR (or AK) build i have not yet started but im seeing high round count being an issue for titanium?. How big of an issue is it?? How well would you say the extra weight of steel would offset the potential issues??

6.5 cm rifle with a 30 cal can for a future 300blk (or 7.62x39) use.

Anyone got a pic of these together? I'm try to justify buying a shovelnose

I have a friend who has a P320 X5 that he wants to suppress and has narrowed it down in between the Deadair Mojave 9 and the Rugged Obsidian 9. He has done some research, and has seen some videos that say that say the Rugged will require some tuning for the 320 but can’t find any videos about the Deadair and the 320. He doesn’t have Reddit and asked me to reach out to y’all to try to determine which of those two suppressors will require the least amount of tuning of his P320 in y’all’s experience. And yes he is dead set on using a P320.

Finally got my approval 5/16-7/20. Love this setup so far. Can’t wait to go shoot it!

i’m not one for vanity plates but apparently this one is available. the temptation is strong

I have a Form 1 that has been processing far longer than the current estimate on the BATFE website. I have seen that an e-mail to the division can accelerate an approval, but haven't been able to find the correct address. Can anyone share it with me?

Thanks!

WAY better with NODs with that extended stock. So happy

In my time researching a dedicated 556 low back pressure can, I see the rhodie 6 come up frequently. Not here to talk about controversy but I had an idea that I'm not sure would work. What if I took the rhodie 6k and added a B&T mk12 reflex hub adapter on it? Has anyone done this or thought of it or am I just too bored?

How far off can we be on the guesstimate before we need to notify the ATF of the difference?

I'm SBRing a Kel-Tec CP33 and this is really the first time I'm having to do a total guess as to OAL.

Just picked up a threaded barrel for my G34 and tossed the Obsidian 9 on to see how it would look. Pretty hilarious if I don't say so myself.

Hello yall, I currently am having a form 1 filed for my galil ace gen 2, 556. I had the barrel chopped to 14.3”, pin and welded. But decided to cut the pin out and form 1 it through dissident arms. I currently have a hux flow 556 TI, and am wanting to look into an OTB suppressor for my rifle as well. It seems my galil has a heavy barrel profile, around .75OD from Google (I don’t have my rifle currently so I can’t measure the OD), so with that said maybe my options are larger if I went with a 30cal can?

Any input would be awesome! Thanks!

But the question is how tight is too tight? Does it start at when its interfering with proper function? I know this definitely fits the bill as it's flat out touching the rail and I'll be getting a slightly shorther handguard to remedy that(10in on it now, going to 9.5).

Actual reason for the post is I finally finished can no 2 from my first approvals last week, ftn4.5 30cal can, absolutely goofily long on a 10.5 but it's stupid quiet from all the reports I've seen and vids I've watched so it'll be the can for when I want it to be as quiet as possible (already got another form 1 sent in to make a more practical sized can for it. Its mostly a fun range toy but since I reload and run powdercoat cast 230gr subs for it I decided it absolutely needed a can.

Living over 50 miles from any NFA FFLs, Capitol Armory is a dream.