Came with a spanner for the mount but attached muzzle device has triangle flats that don't fit a regular wrench. Best way to ensure a secure attachment?

In my time researching a dedicated 556 low back pressure can, I see the rhodie 6 come up frequently. Not here to talk about controversy but I had an idea that I'm not sure would work. What if I took the rhodie 6k and added a B&T mk12 reflex hub adapter on it? Has anyone done this or thought of it or am I just too bored?

The worst part was waiting in silence hoping I didn't fill my form 1 out wrong. Now I have to figure out suppressors. Anyone here have recommendations for good quality?

How far off can we be on the guesstimate before we need to notify the ATF of the difference?

I'm SBRing a Kel-Tec CP33 and this is really the first time I'm having to do a total guess as to OAL.

I have a Form 1 that has been processing far longer than the current estimate on the BATFE website. I have seen that an e-mail to the division can accelerate an approval, but haven't been able to find the correct address. Can anyone share it with me?

Thanks!

But the question is how tight is too tight? Does it start at when its interfering with proper function? I know this definitely fits the bill as it's flat out touching the rail and I'll be getting a slightly shorther handguard to remedy that(10in on it now, going to 9.5).

Actual reason for the post is I finally finished can no 2 from my first approvals last week, ftn4.5 30cal can, absolutely goofily long on a 10.5 but it's stupid quiet from all the reports I've seen and vids I've watched so it'll be the can for when I want it to be as quiet as possible (already got another form 1 sent in to make a more practical sized can for it. Its mostly a fun range toy but since I reload and run powdercoat cast 230gr subs for it I decided it absolutely needed a can.

I have a friend who has a P320 X5 that he wants to suppress and has narrowed it down in between the Deadair Mojave 9 and the Rugged Obsidian 9. He has done some research, and has seen some videos that say that say the Rugged will require some tuning for the 320 but can’t find any videos about the Deadair and the 320. He doesn’t have Reddit and asked me to reach out to y’all to try to determine which of those two suppressors will require the least amount of tuning of his P320 in y’all’s experience. And yes he is dead set on using a P320.

Anyone got a pic of these together? I'm try to justify buying a shovelnose

u/BOE-Suppression u/Comstock-Support

So previously posted about alignment being off with newly purchased Comstock plan b flash hider and low profile hub mount on BOE incolite 9m. I Disassembled and reassembled with direct mount that came with suppressor and alignment rod is pretty well centered (pic 1). Disassembled and dry fit Comstock plan b system again and alignment rod is touching end of suppressor at about the 10:00 position. Took off Suppressor and ran alignment rod with just flash hider and alignment rod is almost touching 10:00 position of flash hider. So at this point can I conclude the flash hider is causing the problem?

As I look into the material of a supressor Im favoring a Ti for my hunting rifles. I do want to be able to swap it to an AR (or AK) build i have not yet started but im seeing high round count being an issue for titanium?. How big of an issue is it?? How well would you say the extra weight of steel would offset the potential issues??

6.5 cm rifle with a 30 cal can for a future 300blk (or 7.62x39) use.

Does anyone have link to an article or video showing the current steps on setting up an NFA gun trust?

I’m looking to buy my first can. Don’t usually have a problem, but my ADHD is pretty bad when it comes to things legal forms.

It be easier on me if I knew what steps to expect.

Thank you!

Living over 50 miles from any NFA FFLs, Capitol Armory is a dream.

Going on an Arsenal Sam7k

Hello yall, I currently am having a form 1 filed for my galil ace gen 2, 556. I had the barrel chopped to 14.3”, pin and welded. But decided to cut the pin out and form 1 it through dissident arms. I currently have a hux flow 556 TI, and am wanting to look into an OTB suppressor for my rifle as well. It seems my galil has a heavy barrel profile, around .75OD from Google (I don’t have my rifle currently so I can’t measure the OD), so with that said maybe my options are larger if I went with a 30cal can?

Any input would be awesome! Thanks!

i’m not one for vanity plates but apparently this one is available. the temptation is strong

Map of where suppressors are legal and illegal for reference.

Finally got my approval 5/16-7/20. Love this setup so far. Can’t wait to go shoot it!

WAY better with NODs with that extended stock. So happy

Hi everyone, just purchased a huxwrx flow range 36 Ti suppressor the other day. I picked it up today, and saw it already came with a QD hub, however, the associates at Scheels told me to go with a different hub adapter from Dead Air. Is there any reason to spend the extra cash for a different one? The huxwrx seems to be the better option due to the QD mount, and I would just need to purchase the muzzle device rather than both the adapter and muzzle device from Dead Air. I'm not too knowledgeable when it comes to suppressors so any insight is appreciated, thank you.

My first ever time using national gun trust and I paid for their instant fingerprint card to eft file. I got the email with the link and used that to access the card now on day 2 of trying to make it work and I’ve reached out to them but every time I get to the generate page it says no valid purchase found. I had an easier time getting my finger prints to work on a silencer shop kiosk.

Full auto ZEV FDP. Post sample machine gun.

13.5 .308 SBR w/ KAC PRS-1 Suppressor!