Knocked out some 43x mos frames. Could only post one in this sub.

Bought a practically new police trade in. I can't leave anything stock. Apex trigger and SLR magwell.

Testing a customer's conversion before sending it to them, I do make them, I will test all kits and it will be a very limited run of conversion kits, Around 10 to 15, No rush.

First Glock, and I’m extremely happy with it. I’ve always been a SIG guy, so I’ve been holding off for years. Once the Gen 6 was released, I knew that was the one I wanted.
I can’t wait to get it to the range. It seems like everyone goes for the 45, but I prefer the feel and look of a full-size pistol. No regrets—I’m excited to see how it shoots. Any must-have upgrades anyone recommends? I’d appreciate it.

So I had a buddy of mine hand mill my 19x slide to directly fit a holosun 507c x2
We copied the dimensions from his Glock 19
But decided to cut it shallower because it would be cutting it close to extractor
After milling the slide we notinced a small hole that is right besides the fireing pin safety and spring.

Is there a fix or is it safe to use as is?

Just ordered a gen V G26 lower. Can any confirm they've used this adapter with a G19 gen 3 slide??? Idk the difference between G26.4 and G26.5 frame geometry, or if this will even work because the website doesn't list G26 to G26L at all on the compatibility list.

First off, I don't own an Osight, all my pistols have RMR's, RMR-HD's or Holosuns, so I don't have a dog in this fight. Hell I've even ragged on the poors in the past for their Osights, but it looks like I might have been wrong. 6,000 rounds at a very accelerated firing schedule seems to be a solid test. I don't really trust any guntuber 100%, but Chris from Regular Guy Training seems to be a pretty straight forward dude.

I did find the dig at Cylee funny I must admit, and I will still continue to rag on the poors for using those pieces of crap, but as far as the Osight XE AMRS is concerned, it seems solid. Now of course this is one single data point and I'm sure I'll get a bunch of people in the comments saying theirs broke and it sucks and I'm a complete idiot, etc.., so take everything with a grain of salt

OEM fanboys are going to hate me so lets hear the shit talk on my $2000 43x.

Build List:

-radian magwell
-radian ramjet afterburner ported
-oem slide with a window cut
-osight se multi reticle
-tlr 7sub
-antimatter wing
-henry holster
-shield arms mag release
-ndz 15 lb recoil spring
-apex trigger and OP connector
-extended slide lock
-kiral 2 piece backstrap

Total: $2070

Yes I know I’m going to get hate for it. I’ll probably go back and clean it up at a later date but it works with all mags now so I’m ok with it.

Glock 47 MOS
OP’s Glock Performance Trigger
C&H Precision 509T MOS Plate
Holosun 509T X2 Gold Dot
Streamlight TLR-7 X
OEM +2 Magazine Extension

(Suppressor-height backup irons for co-witness on way) 🥲

Hey, looking for some advice on stippling a Glock.

Has anyone had theirs done by Sonoran Defense or Monsoon Tactical? I’m wanting a decent stippling that’ll just be better than the standard Glock .

I wanna put an frt on my gen 5 Glock 23. Any recommendations pls!

Looking to get into limited optics with my Glock 17 gen 4 and am looking to add a brass plug to the grip for extra weight. What are the best options to do this is an older SLR magwell? I've heard about milling down regular brass plugs, but how you would prevent it from rattling? I have also heard of the option of using tungsten putty/balls in place of a plug. I am not opposed to replacing the magwell, but the next one just needs to fit taran tactical magazine extensions.

Came out pretty good if I do say so myself

I think there’s still a little bit of un-stippled surface area, may go back over it again

Edit: I can’t believe nobody has noticed the Armslist tag in the photo. This abomination is not mine, but I came across it and couldn’t help but share the handiwork.