Cmmg fixed ejector upper, cmmg metal form mag reliability kit, bad attitude lower. Custom 10.3” cmmg barrel.

Not sure if this fits under ar9 or not but wanted to show off my defender. Tax stamp finally got approved yesterday.

Mpa defender with side charging upper

Holosun aro spr evo

A3 telescopic stock.

A3 vert grip

Rugged obsidian 9

Hey there! I'm wondering if anyone has any experience with a couple of setups. This is my first time dipping my toes into the world of AR9's

A little preliminary info, barrel is a 16" Faxon, bolt is a Faxon. Starting out with ExoMags to see if it runs before investing in a dedicated lower or tinkering with any mag adapters.

One buffer system I am thinking of trying is the Kynshot RB5015HD in a standard carbine tube with a standard carbine spring. This would be for a quick swap out in a standard carbine lower that's normally used for a 5.56. Has anyone tried this? Does it work okay?

The next one is building a dedicated lower, but since it's hard to find the JRC extended tube to use the classic GRS, I was thinking of the Tubbs 300BO flat spring, the Kynshot RB5015HD and only one Kynshot spacer weight in an A5 tube. Has anyone tried this? The only similar setup I saw to this on Blowback9's blog had the KAK buffer, I believe.

Thanks in advance!

So I got my hands on a Hoffman trigger kicker. Arrives on Monday. My total mass is 21.3oz. So damn close to 22. I know I might have to up the mass a little. But my real question is the bolt that I have. Looks like the picture on the trigger kicker guide from Hoffman tactical site, kind of. The bottom of the bolt is not “demilled” as it describes on the site for the ones that do not work. What do you guys think? Top bolt on the photo from the site is the one that works. Bottom bolt is the one that is incorrect. I’ve also included photos of my bolt carrier group. Any advice would be awesome! Thank you ar9 fam!!

I have a question about the buffer. I'm considering a KVP 10oz + AR15 tube + carbine tube and the GRS configuration. I want it for self-defense, shooting range, and competition. Which one would you recommend?

My Spike’s Tactical ST9 Colt mag lower has been fantastic since I adjusted my ejector properly. It has been running smooth for a while with two different uppers (4.5” BA EPC barrel w/DA Wolfman on Atlas mount tucked and a 5.5” BA EPC barrel with and the DA Wolfman about half the time).

The buffers I have used have been a Maxim RDB carbine length with a Law folder and anarchy outdoors bolt extension, the GRS with Law folder and a KAK heavy carrier extension, and now a KAK mini milspec buffer tube with a Maxim RDB CQB. It’s installed correctly, no preload or slop.

The other day I started to get bolt lock back on the last round and the Bolt catch became very hard to depress (empty mag, full mag or no mag). I use Duramags

The bolt catch appears to be canted. I reached out to Spikes Tactical Monday morning via phone call and email. I haven’t heard anything yet.

Anyone else experience this?

My birthday boom stick submitted for your pleasure…

Saint Victor PDW AR-9
Sig Foxtrot MSR Compact light w/pressure pad
Burris Fastfire E enclosed optic on a generic ACRO riser
Breek Arms Warhammer charging handle

- 5.5" BA EPC barrel

- Comstock plan B mini brake

- Rearden Atlas (OCL Milkman on the way)

- 5" UTG Pro Arwen

I think this is literally the best possible fit. Not touching the handguard, wrench flats are still exposed, but its still minimal gap.

The UTG *PRO* line have always seemed underrepresented to me IMO.

Noveske Cry Baby with a PTR Vent 2.

I’ve had this PCC sitting in a closet a few years now. Had never put more than 20 though the barrel. The other night I got it out to shoot and confirm zero and come up with some plans. Then I took one more shot. I am u familiar with bolts/BCGS like this. But like I said. This is my first PCC and I’m finding confusing details about it. Can anyone point out to me what’s wrong. It randomly just started double feeding every round and won’t even attempt to eject. Any help here would be appreciated. Trying to get this thing back to start running and building around it.

Upper is a Wolfpack AR45 with an 8 inch barrel
Lower is a New Frontier AR45 lower

Playing with optics on it now and just had a random Vortex and magnifier on it.

Any input and education is welcome. Just trying to learn here guys.

Anyone got an AR9 that they run with an LVPO? Toying around with this idea and looking for inspiratiom and ideas. Share experience with shooting ranges (100 yards? More?) Thanks!

My buddy wants to build one but they arent anywhere on the site anymore? Are they just OOS so they dont show up or discontinued?

I have a PCC 9mm that I built a few years ago and it runs great and never had a issue. I did the Anderson because accepted Glock mags, I have the G26 Gen 5. I purchased a Staccato HD P4 about two months ago, my first one. Unbeknown to me the LGS owner said it takes Glock mags so when I went to our local range I informed the RSO and he pulled his mag out of his Glock and ran out his Glock 17 mag in my Staccato

It never occurred to me before until today so I tired the Staccato HD P4 mag in my Anderson PCC build and it was a no go. The mag catch-release does nothing. Then I tried the Staccato mag in the G26 and it works perfectly. Anyone know the reason why the Anderson lower won't accept the Staccato mag? The Staccato accepts Glock mags and the Glock accepts Staccato HD P4 mags but the Anderson only accepts Glock mags. Thank for looking

I am new to the platform and noticed after 30 shots or so, the adapter was backing off the threads a little at the barrel end. So, what non permanent solutions are you guys using to keep your BRT adapters from backing off while shooting?

I just ordered the Atrius Super Selektor and then went ham with my Dremel. How's my handiwork? Also, I know my lower is low shelf but what the heck is that other cutout on the left side?

8.3” ba barrel
cmmg zeroed 46
dnt ss
kvp 10oz
griffin 11.5 sr handguard

Currently a pistol due to my state laws. Once i get a long enough barrel, itll be an SBR

Parts List:

• CMMG Banshee FE Upper Receiver + Bolt
• C3junkie 8 inch barrel + thread through trilug
• BCM 7inch rail
• Arisaka Indexer
• Sparrow Dynamics mlok rail covers
• Scalarworks peak irons
• Scalarworks 1.93 + sig romeo 4t pro with 3d printed cover
• BCM mk2 buffer tube (A5)
• C3junkie flat wire spring
• Kynshot RB5007
• SBA5 brace
• G$ ultra duty lpk
• B5 P23 grip
• G$ SD-E
• GA SN-ACH Gen 2
• CMMG Gen 2 9 ARC Mags
• OCL Milkman (enjoy this can on my smg)
• Rugged Universal trilug mount

Over the weekend i went to the local indoor range with my BIL. Goal was to function test a few project builds. I was only able to put ~120 through this one since I was testing\tuning two other guns. Shot about ~75 unsuppressed using 115gr Academy\Monarch headstamp (magtech) branded ammo with no issues. Also ran ~45 147gr subsonic HSL remans, and had two issues.

While shooting this suppressed, I was disappointed with the amount of particulates hitting me in the face. My BIL noted he wasnt getting any shooting right handed (just a little gas). But, I shoot left handed and was constantly getting peppered. Consdiering my parts list, feel like the bulk of the particulates are coming out the ejection port?

Seeing if the community has other recommendations for particulate reduction? Some things I can try next:

- My first thought is perhaps "dirty\weak ammo". I have some 147gr FM Hush ammo and 147gr Lawman clean fire i can try. Whenever syntech comes back in stock in bulk ill see about getting some of that.
- Second thought was, test my other flow through cans (flow 9kti, b&t sqd m 9, cat mob).
-Lastly, I did some quick search and saw a guy named zentradi on ar15 fitted a colt smg gas deflector to his FE upper. https://www.ar15.com/media/mediafiles/14200/zflection1_jpg-3756824.JPG i need to sign up there to get some more info from him on that.

This is my first AR9, i run a integrally suppressed (novox) cz scorpion and dont get any noticeable gas\particulates, Then also my smg, a mac11a1 with a Lage Versa-12 upper (running scorpion mags). Again no noticeable gas\particulates to the face.

Besides the suppression issue, the RDB system shot extremely soft! To the point where when running subs, once in awhile i would get FTF\FTE with the HSL subs.

Shoutout to u/amphibian-c3junkie in answering my many questions over the past month or so. Once he gets longer barrels in, i can complete my AR9 SBR build.

SBR
Angstadt 6” barrel
Endo mag fed
Cut down Midwest handguard
Faxon bolt
Kynshot hydraulic buffer
Tubbs lightweight flatwire spring
Atrius selector
Dead air Wolfman (shown short)
Eotech on adm riser

Runs extremely well and extremely fast

Luth Stripped Upper
DPMS Lower
Trybe Bolt
RIA 10.5” Barrel w/ A2 9mm Flash Hider
Colt Magazine Adaptor
DURAMAG magazines
CMMG Brass Deflector & Dust Cover
Midwest Industries FSB Picatinny Rail
Aimpoint COMP M
Surefire 660 w/ VLTOR mount
BCM Grip

Built out a Colt mag 9mm a few months ago with Magpul furniture. Decided to reskin it and literally just got this done yesterday.
I made the change to be able to use a colt GI side sling mount, which the Magpul SL handguard precludes. I just never trusted putting a sling mount into un-reinforced polymer. I also think the classic carbine furniture looks better with the CAR brace.
It will probably get a FSB light mount, but holding off on that for a bit.

Furniture is B5 OD green. Quality stuff, not cheap crap. The addition of a hinged grip compartment was a nice touch.

A buddy got a FM9 and wanted to get into FRT's

This is probably the easiest way to get a AR9 FRT going.

5in FM9 dual charging upper with the A5 tube and RMB. Going to get him to order a Flat wire spring to top it off.

Real basic GMR super safety with a AS designs trigger shoe that I had laying about.

Gun is super easy to lock down and doesn't move a lot. Able to hold a 3-4 inch group at 15 yards. Runs about 800 RPM.

Has anyone ran any of the expo arms upper? They got a sale right now and I'm tempted to buy the 8.3" but don't see much info on them or the feed cone in particular. Seeing if anyone has had any experience with them.