-Enviro E30
-Heat & Glo Supreme 30
-Kozy heat chaska 29

Anyone have experience with these gas inserts?

Want something that’s dependable and easy to work on if needed. I will be using propane, which I’m told can be more harsh on the burners. Any input is appreciated. TYIA!

Went with wood burning. Very easy to clean

Humoring the idea of painting the hearth around our wood stove.

Not sure if I need heat resistant paint on the whole thing or just the parts closest to the wood stove? Or at all?

Anything else I should consider?

I do not know what the model number of this fireplace is. It’s about 25 years old I’d like to at least replace the yucky looking materials on its floor . What should I do to do it safely? Or should I just leave it alone? We are selling this condo.

Hi all,

Probably a stupid question but does anyone know if it's possible to modify a dual sided gas, direct vent, fireplace to work in an existing fireplace cut out (set up for direct venting)?

Any assistance would be greatly appreciated.

I bought a new glass door cover for my fireplace but it doesn’t specify if you can use it for gas. It doesn’t say for wood burning. Is there really a difference? Pic is of the current one, new one is still in the box.

Hey everyone, I recently took a look under my masonry fireplace(image 1)and I believe that it has some serious build quality issues. Several areas between the bricks lack mortar( 2 & 3). One area appears to have a cavity from a leftover cut from the herringbone(2) while the other is filled with mortar(3). There is exposed insulation above the damper(4) and some of the bricks below the terracotta flue are not covered with mortar(5). This fireplace was built in Seattle, Wa in 2006 and was never used. I am not sure whether it is a precast kit or built from the ground up. I would greatly appreciate any input from someone who knows more than me.

Pilot light is too too high for this this fireplace. How to open the panel to adjust the pilot lights? I removed 4 screws from the bottom panel, but looks like there are two large bolts going through the bottom panel vertically, holding the fireplace unit.

We recently uncovered our fireplace in our house that had been sealed by the previous owners. Unfortunately, it was unusable as it was, so we had to build a boxed surround. I'm looking for some ideas on how we can decorate this now... I've included an AI generated image of one idea we had (hence the wonky pattern and the whole oak base), but I just wondered if anyone had any other ideas? The marble will definitely be replaced as its so scratched!

Hi All,

I've been living in my upstairs apartment for just under a year now, and have this fireplace in my living room. Its an old building I live in, which is situated on the high street of the town I live in. I can't determine whether it's original and has been blocked off at some point in the past, or whether it's been put in for decoration in the recent past. Either way, it has been a bugbear, and on my mind to get an electric fire installed in the centre of it, to set the room off and make the place look good. Any advice on how to go about this would be appreciated. I live in the UK for reference, and have been looking on B&Q's website at electric fires.

If you have a fireplace with a short lived solid bar log grate that burns up every few years, you really need to switch to a tube fireplace grate heat exchanger. Since they have a fan forcing the hot air out into your home the steel holding the fire does not get hot enough to glow red hot where oxygen attacks the surface causing the scaling that makes solid bar grates burn up.

Instead all that heat conducted from the coals blows out into the room adding a magnitude of additional heat into your home that you would otherwise not get from your fireplace. In our experience we no longer need to keep our socks on mid winter.

Pro tip after many years of experience: spread out the hot coals across the bed of tubes to get the most heat and keep the ash scooped out from below for good combustion airflow.

I live in an apartment unit that has a wood burning stove (bet you don't hear that often!)

It's either poorly built, or has broken parts, as the air vent control does nothing, and there's always a strong draft bringing outside air, dust, pollen... and now wildfire smoke (a bit ironic, no?)

Anyway, I want this thing temporarily sealed off while I live here, and saw that an inflatable chimney balloon might be just the thing I need... but for the life of me I cannot find them for sale in Canada, only US and UK.

Suggestions? And I'm not DIY-ing something, it's gotta be fire-rated, or made specifically for fireplaces, for insurance reasons.

TIA!

I've got a fairly large fireplace and a log burner. The walls in the house have cavity wall insulation but not behind the fireplace. This means (when the log burner isn't on) we're losing 4-5C in heat making a difference to the temperature in the room.

As long as I leave enough of a gap behind the stove (instructions say at least 500mm: https://stovebuddy.co.uk/wp-content/uploads/2021/08/Buddy-5-Wide-User-Guide.pdf) then is it ok to insulate the walls with fire resistant material?

I'm thinking of: Rockwood RW5 (https://www.rockwool.com/uk/products/rw5) followed by a Vermiculite Fire board on top.

Would that work?

Hello, my wife and I recently purchased a new home and we really want to add a mantle above our fireplace however we’re a little unsure how best to do so.

The previous owners installed this sheet rock over drywall, which we like, but it complicates mounting a mantle to it because it’s not a flat surface.

Locating the studs framing the fireplace shouldn’t be too difficult and I’m confident I can attach the hidden bracket system to the studs, but my concern is that the mantle won’t be flush with the rocky surface because it isn’t flat.

I’d really like not to have to remove some of the sheet rock, but I’m curious for folks and similar situations what they have done. Also, any recommendations on color would be much appreciated. Thanks for the help.

Hi everyone! Brand new to this sub and could use some advice...

I live in a Victorian flat in the UK. When we moved in, there was a working gas fireplace in the living room. We were delighted and used it for the first winter, but then noticed that we could not find any trace of recent servicing having been carried out by previous owners...we tried to get it serviced and discovered it had not been serviced in twenty years and was a major safety hazard and had to be dismantled!

We took it out and were left with a crater cavity as the insert was massive and had a marble surround. So far all we've done is plaster the sides so it wouldn't look like too much of a mess. My question is: if we wanted to get a gas stove like in the inspo picture, what should we be looking to do with the floor/base of the cavity? Is it fine to just lay a slab of concrete, or does it need to be stone? Bare in mind that the subflooring in our flat is wood, but also the fireplace is original, has a chimney+some remnants of original tiles beneath it and what looks like bricks at the back.

Thank you in advance!

Hi everyone! My husband and I moved into our house this March. It's almost 100 years old (built in 1937 or around then) and has this fireplace in the living room! I can see a dark color (I think black paint) under the white paint. Trying to decide whether we should try and strip the paint off to see the wood underneath!
If anyone has a house around the similar age or a similar fireplace I'd love to know what you've done!

Looking to install an electric fireplace insert in my basement. As you can see in my photo I did some measurements.

I suppose I’m curious if I should be trying to find an insert that is nearly 36” wide (blue line dimension) as it is the width from the stone side to side.

Any other recommendations based on what the photo shows would be appreciated as well.

I'm moving into an abandoned house and need to inspect the fireplace soon. It apparently needs repairs before winter. I have a few questions:

What should I look for during inspection?

How do I know if it's repairable?

Can I repair it myself, or do I need a professional? (I haven't been able to find inspectors in the area.)

Since I haven't been able to find anyone to fix it, I suppose I need to do it myself, and I have zero expertise in fireplaces 😞 Hope I can figure it out.

I'd appreciate any advice you can give.

Thanks!